Leaderboard

Hi, I’ve just stumbled onto this forum, and i figure I’ll probably need to post here eventually acquired my luminator last year, 2nd owner from a grandma. 70000 (got w 55000)miles. Here’s some pics; thx yall

The *actuator* was discontinued approx 20 years ago.......finding an NOS piece would be a challenge. The item IS serviceable..........

Good day, I have been a W body enthusiast since high school 04. In my student parking lot, we had a 93 Gran prix, 94 olds cutlass supreme, 94 cavalier z24, 95 monte, and my lumina z34. These cars were everywhere! My first car was a 94 lumina z34 (still have it). In 2012 I put a 4.9 PFI in it and it is almost complete. I just need to replace the rear suspension and odds and ends. I have a 99 Monte (needs some work), and I just picked up a decent (needs some work) Cutlass supreme. I am buying a new top for the cutlass on Friday. I want to get black canvass instead of the white (the car has black leather interior). They come in black, grey, white, red. What do you all think would be the best color? Just curious. Very few of these ole buggies still around (at least in my area). I thought I would join the forum to see what you all are up to (I feel very late to the party). I already have seen some super nice examples of these cars (nice job everyone!). Ill post more as spring hits and I can get them out, and work on them more. Also, not adverse to loading them up on the trailer for any meets that might happen. Thank you! Hope you all have a wonderful day!

Thanks all for this. As of the moment the car is in storage do it will be a while before I can check it out, but I will say I get more & more confident this will be the cause. It has been happening for a long time. Form the day I bought this car in Oct., 1994, I always wondered where a quart of oil was going every 1000 miles or so. My money is on this as pictured above, it was probably badly sealed to begin with. And these things don't get better, only worse. I went in and checked my 2020 repair bills from when I had the intake manifold gaskets replaced. The mechanic also replaced the gasket for the part 10130955 as you see in the photo but no mention is made on whether the distributor plug seal was addressed so I am going to assume it was not. While it's a shame all that work that was done to the motor back then would have to be re-done just to get at what needs to be repaired, so be it. Even if I decide to get the rear head pulled to replace the O-ring rather than trying my luck with sealant, that's still way better than having the entire motor pulled. I might as well go the whole 9 yards and have both head gaskets replaced for a one and done job. I should be getting the car out of storage within the next few weeks, I'll keep all posted on how things progress, and thanks again, much appreciated!

Hey everyone, My name’s Ryan, I’m from Long Island, NY, and I’m new to the Monte Carlo platform. I recently picked up a 2003 Monte Carlo SS and I’m excited to finally start a build thread and be part of the community. By trade I’m a licensed marine engineer, so I’m very hands-on mechanically and enjoy learning the technical side of things. On the automotive side, I’ve worked on and tuned a variety of platforms, everything from basic bolt-ons and wiring to full tuning using HP Tuners, Hondata, and standalone setups. I enjoy both the mechanical and tuning sides of builds and documenting the process. For the Monte, the plan is to start simple, catch up on maintenance, fix worn components, and do some basic bolt-ons while I sort out the body and cosmetics. Once the chassis and body are in better shape, the goal is to turn things up. I’m currently torn between a Gen V M90 top swap or going turbo, but either way the end goal is a "reliable", fun street car that still rips when you get into it. I’ll be sharing progress, asking questions, and learning as I go. Looking forward to seeing everyone’s builds and being part of the community.

Greetings forum members! New member, so thought I'd take a moment to introduce myself. Last Spring (2025) I acquired a relatively pristine (54k miles) 88 Pontiac GP SE. I hadn't even known they made these with a 5-speed, so I hadn't explicitly been looking, yet lo and behold here we are. I've got it on good authority I'm only the second owner. It started life in central NY but spent the last 10 years parked in a sweltering hot garage in central Florida. It was never ever even registered in FL. So it's got some internal heat damage, which I've been repairing. The door upholstery glue had given up years ago. The stereo was a mess, but I replaced all of the capacitors on the amplifier boards and even plumbed in a bluetooth module to the cassette inputs. I'm not much of an auto mechanic myself, I do cybersecurity for a living, but I don't mind getting my hands dirty on projects like this. On the serious mechanical side, I've had it at a local "rural mechanic" who's did a flush on all of the fluids, changed out the master/slave cylinders, and replaced the brakes. I seem to have dodged the bullet of any serious rust or corrosion, but I know these are prone to rotting out their rear strut towers so I plan on installing a strut tower brace and blast the insides with as much cavity wax as they'll take. Any other "gotchas" tips, tricks, or suggestions for keeping something like this roadworthy? Google's AI guestimates, based on statistical analysis of scrap rates versus production numbers, there may only be 15-25 "roadworthy" versions of this model, trim, and transmission combinations left anywhere I didn't buy this planning on a super rare preservation "duty" yet here I am...any suggestions would be greatly appreciated. Don't worry, despite living in the salt-belt, I don't plan on driving it in winter for that reason...I do hope to drive it during the warmer months though! An 88 GP was my very first car when I turned 16, so I'd always been looking for a decent one, "just for fun". I never planned on ending up with a bigfoot-riding-a-unicorn of rarity...something I'm not all together happy about...yet here we are!

anyways, welcome to the site.

You're in the right place because we love our W-bodies here. Welcome!

Does the pump run? If it does, unhook a fuel line under the hood and jump the fuel pump relay.

Its likely a pre-production thing that never carried over, as that episode was filmed prior to the 88 cutlass being released.

Automatic equipped FE3 springs from a 3.4 DOHC car seem to be the stiffest. The manual trans springs are slightly less stiff (as compared side by side, and they have different part numbers). In other words your automatic Z34 has the stiffest ever available factory.

I know it's been done before. I think the biggest issue is always switching the vehicle over to OBDII. But if you aren't going for a Series II L67 a Series I L67 from a Bonneville that is OBD 1.5 might make a better option.

What they liked the best: The brakes. What folks complain about the most on this site: The brakes. I've said it before, I'll say it again: The biggest problem with Gen 1 brakes is not the brakes per se, it's the brake booster.

It's that time. The oil leak in the rear main seal of my 1994 Cutlass Supreme SL with the 3.4L motor has gotten so bad that it needs to come out for repairs. In addition to this being in need of replacement, I am going to have the oil pan gasket replaced as well, along with the 3 coils and the alternator while the motor is out of the car. In addition to that, is there anything else anyone can think of that should be replaced while the motor is out, as this would be a golden opportunity to get it done. The engine compartment will also be degreased to clean up the big mess this leak has been making. It does not need a timing belt, water pump, or any intake manifold work as this was all done 5 years and 10,000 miles ago and no issues here.

I was able to replace the o-ring and add an extra gasket with the information from the old double gasket thread all without removing the rear head. I also put RTV on it and it never leaked in the 10+ years I owned the car after the repair.

One should have the service manual within reach for electrical diagnosis.

I wanna see pictures of the Gran Prix, never seen one before! /s Welcome!

So my hunt begins for an intrigue with the 3.5, I'm looking specifically for a GL or GLS with the 3.29 gear ratio. Anyone know the RPO code for that to help me in my searches? Google and rpocode.com aren't helping me

This is the only device that will separate the fuel line from the rail.... there is another method you might try.... raise the car up high enough to get under comfortably & disconnect the fuel filter from the fuel line (one end of the filter makes used of threaded connection , the other end is the same ac/fuel line quick disconnect slip-on connection). Once again run a length of hose long enough to clear the car & fill a gas container to drain the tank.

The fuel lines that feed the fuel rail are not screw on nut fittings, both the pressure & the return are disconnected with a set of fuel line/ac disconnect tools. The pressure line is near the centre at the back of the engine. One pulls off the engine cover & you'll see the fuel rail. Once you've disconnected the line you'll need a lengthy section of garden hose to slip over the fuel line end & tape it up to prevent any leaking & feed it into a container size of your choosing. Now you can bypass the relay to power up the fuel pump to drain the tank.

87 to 30

Hi guys, I'm still alive and well and still have dome light switches! The site used to send me an email when someone posted on this thread, not sure if that doesn't work anymore? My direct email is mezz@benris.com if anyone else is still looking or switches.

absolutely

spammer?

Thank you(I hope I replied to your comment the right way) will definitely taking care of her best I can. As per my city; I’m located in Philadelphia.

I guess I've been here long enough to say this, why are we bumping 15 year old threads? I didn't even read the comment, but it sounds like it's a bot that is advertising.

was this badge a 88 or maybe 89 year option or standard feature? i've never seen that besides in this video

I do not believe that the 1994 Cutlass Supremes had the "Audio Bass Control" slider switch as an option, but I am not certain of this. The slider was located below the fog light button if the car were so equipped (there were two versions of the fog light switches). Here's an image of one (sorry it's so big): If the car was equipped with this feature, it also had a small amplifier located behind the dashboard, to the left of and slightly below the instrument panel. My 1992 Cutlass Supreme was pre-wired for this feature. The harness was folded and taped under the dashboard. I had a hell of a time getting the amplifier out of a junkyard car. The slider does definitely make a difference in the bass response in the 6x9s. It's been a really long time since I've posted here. I still love this site because it hasn't changed and people are still tinkering with their Ws.

What you see is actually *6PY* ....goes with *7PY* possibly front suspension FLH *6PY, FRH *7PY* 6PY 4 2 0 3 7 P FLH M COMPONENT FRT LH COMPUTER SEL SUSP (6PY) 8 9 0 2 0 1 E 1 E A 7PY 4 3 3 3 3 P FRH M COMPONENT FRT RH COMPUTER SEL SUSP (7PY) 8 9 0 2 0 1 E 1 E A

amended

I should have specified contacting a spring shop that specializes in making custom coil springs like this website https://www.coilsprings.com/classic-car-coil-springs No idea what numbers you'd have to give them, I wish I had a spec sheet from a discontinued aftermarket performance option for reference but I imagine those are very hard to come by.

There are no longer aftermarket *performance* springs manufactured for the 1st gen W's, if you've got the FE3 suspension under the car then you've already got the stiffest springs available. I take it that you want lower the front to match the dropped rear's ride height?

I’m leaning toward an injector issue. Belt and tensioner are new with the engine install. Vacuum lines are good. I’m going to replace the MAP and TPS. Definitely seems fuel or air related.

Ive been getting water collecting in the spare tire well in the TGP and havent been able to figure out where its coming from. Thanks for mentioning the sealer failure, I will take a closer look.

When retracting...... the entire glass frame lowers to below the roofline & then retracts along the runners to the full stop position at the back end of the runner assembly. When the assembly is in the *closed position* the glass is flush with the roofline exterior.

I ordered one to try. Thank you. I’ll keep you posted if I have questions about it.

Putting all of the *hardware compatibility* aside for a moment.... what ECM/PCM are you using to drive that L67? Are you using the 1227727 case or the 1614936 case?.........with a burned chip tune for an eeprom These are OBD1.. or are you using an OBD2 pcm?

I'm going to differ with you on this Kyle....... what OP needs is the necessary A/C piping from a 1st Gen Regal with the 3.8 engine. If you intend on keeping as much as your car is currently fitted with you'll need the a/c compressor manifold hose assembly that was fitted to the 3.8 Regal & a new rebuilt pre 94 compressor. Everything prior to 94 is R12 based, everything post 93 is R134 based. When GM introduced 134 in 94 they changed ALL of the A/C line fittings thread pitch so NOTHING from prior & post can be used together. My suggestion to you is to keep your 92 car all 92, get that old 92 3.8 manifold hose assembly & purchase a new *rebuilt* pre 94 A/C compressor, even the manifold hose assembly changed in 94 because GM redesigned the back end of the compressor housing for 94 so the old manifold hose will not attach to the newer design compressor housing. Purchase yourself a new receiver/dryer as well as a new orifice tube. Go into Rockauto, search 92 Regal, they still house most of what you'll need.

Yeah, that makes it sound even more like the brake lights are the turn signal switch in the column... 1994-2001 Gen 1 and Gen 1.5 Turn Signal Switch Replacement | W-BodyTech Forums But that shifting thing...are you able to turn the key and move the steering wheel? Can you shift out of park with the steering wheel unlocked but with engine off?

When I first saw this I was wondering why this logo was placed on the door handle.

Gotta love that quality 80s GM fit and finish! And that Regal is very oddly equipped. Bench seat, manual locks and windows, no rear reading lights.....but it has alloy wheels. Then there is this: That cluster must be from a pre-production vehicle, as the tach was never red like that on any of the production ones. My old 88 Regal was a November 87 build, and the tach was green like the rest of the cluster.

BCC= AXSJ2368 Scan id= 2391 Part number= 16162364 Release date= 11/09/90 Engine size= 3.4 Trans Type= Auto trans ECM/PCM: ECM #16149396 Used in cars: Chevy Pontiac Oldsmobile Possibly used in: LUMINA LUMINA EUROSPORT LUMINA Z34 GRAND PRIX LE GRAND PRIX SE GRAND PRIX GT GRAND PRIX STE CUTLASS SUPREME SUPREME INTERNAT'L CUTLASS SUPREME SL CUTLASS SUPREME CONV Options: With LQ1 3.4L GAS 6 CYL (3.4X) SFI OHC V6 HO With M13 AUTO 4 SPD (4T60-E) With NA5 FEDERAL REQUIREMENTS With QGW ALL P215/60 R/16 N BL R/PE ST TL HWY With QXJ P225/60R16/N NL R/PE ST TL AL3

91 auto which is what I have in my 91 GP is the AYSZ, AUSJ is the T code engine (3.1) W body for 91, AUBU is the T code engine W body for 93 auto trans these all come out of the 16149396 ECM I have nothing on the ASXJ

AYSZ = 1992 LQ1/Auto BBUK = 1993 LQ1/Manual BCFA = 1991 LQ1/Manual BCFA is the one you'll want to use

the last 2 3400 swaps I did used 3.1 injectors on stock obd1 ecm's and they both run fine. the bigger injectors will make more power with a tune, but the first thing I would do is start with a better fuel pump. when I first put the 3100 in my old 84 cavalier I went to the track then swapped to a Camaro LT1 fuel pump and went back the next weekend with no other changes an dropped almost 4 tenths off my ET. if I was doing a basic (stock) 3400 swap on a obd1 car I would use 96-99 3400 or 3100 injectors with matching fuel rail (2000+ injectors will not work on stock ecm) or 2.8/3.1 injectors with a 2000+ 3400 fuel rail that has the higer pressure regulator. But if I was mooding a 3400 and dropping it in I would use injectors sized for the fuel requirements of the engine and a full tune.

The '93 3100 used the exact same ECM as the 94-95 models.

I was the one doing that swap, and if you're going to run a 3400 it's definitely worth it. You don't want puddle fuel injection on a 3400. The hardest part in your case would be repinning the C100 connector to your car's pinouts. Also, if you plan to use the same tranny you have now, that will require doing wiring changes on the harness, or you can just use the tranny for the 3400, and you're set. There really wouldn't be much more beyond that. Mine was a PITA because I had to convince my ECM that it's controlling a tranny when it is in reality a 5 speed.

i got the front end by exchaning the motor (0 mile dohc) and a few hundred for bumpers and hood, the hood had really bad rust on the front lip so it was junked and i bought a new one for $300 so i'm not sure how much they go for but i know it's more than a few hundred. Later Jay

did i change my front end!? LOL i changed my whole car! j/k but yeah i did i put all the parts from the Z34 coupe on my base model 4 door, and the side skirts are from Razzi. I got a n ew white paint job and all the parts and labor for about $5500. lot of money i know but i love my car, next is to sell my coilovers and get a air cylinder set up. Later Jay check out my www tab on the bottom and see what it used to look like