All Activity

anyways, welcome to the site.

I wanna see pictures of the Gran Prix, never seen one before! /s Welcome!

Thanks all for this. As of the moment the car is in storage do it will be a while before I can check it out, but I will say I get more & more confident this will be the cause. It has been happening for a long time. Form the day I bought this car in Oct., 1994, I always wondered where a quart of oil was going every 1000 miles or so. My money is on this as pictured above, it was probably badly sealed to begin with. And these things don't get better, only worse. I went in and checked my 2020 repair bills from when I had the intake manifold gaskets replaced. The mechanic also replaced the gasket for the part 10130955 as you see in the photo but no mention is made on whether the distributor plug seal was addressed so I am going to assume it was not. While it's a shame all that work that was done to the motor back then would have to be re-done just to get at what needs to be repaired, so be it. Even if I decide to get the rear head pulled to replace the O-ring rather than trying my luck with sealant, that's still way better than having the entire motor pulled. I might as well go the whole 9 yards and have both head gaskets replaced for a one and done job. I should be getting the car out of storage within the next few weeks, I'll keep all posted on how things progress, and thanks again, much appreciated!

You're in the right place because we love our W-bodies here. Welcome!

Good day, I have been a W body enthusiast since high school 04. In my student parking lot, we had a 93 Gran prix, 94 olds cutlass supreme, 94 cavalier z24, 95 monte, and my lumina z34. These cars were everywhere! My first car was a 94 lumina z34 (still have it). In 2012 I put a 4.9 PFI in it and it is almost complete. I just need to replace the rear suspension and odds and ends. I have a 99 Monte (needs some work), and I just picked up a decent (needs some work) Cutlass supreme. I am buying a new top for the cutlass on Friday. I want to get black canvass instead of the white (the car has black leather interior). They come in black, grey, white, red. What do you all think would be the best color? Just curious. Very few of these ole buggies still around (at least in my area). I thought I would join the forum to see what you all are up to (I feel very late to the party). I already have seen some super nice examples of these cars (nice job everyone!). Ill post more as spring hits and I can get them out, and work on them more. Also, not adverse to loading them up on the trailer for any meets that might happen. Thank you! Hope you all have a wonderful day!

If you need to pull the engine, I may consider the following: - the block mounted crank position sensor. They often get stuck in the block and break. You either need to drill and put a screw in them to pull it out or they break too bad and you need to push it into the oil pan and hope it doesn't cause issues or pull the pan. - Steering Rack ensure there are no leaks. Much easier to do without the engine in the car. - Engine and Trans mounts

I've ground the top ridge of the pump drive down slightly to allow for more room to work, then use a distributer gasket for a Lumina van with a 3.1, just give it a cut and slather it in RTV, seems to work well. and I'll be damned if I'm pulling a head just for that.

It's in the valley right by where the transmission and engine block are joined together. Oil will pool around the distributor plug (also called "oil pump drive") and run down the side right where the transmission mates to the block so where it drips on the ground looks very much like a rear main seal. An O-ring goes bad on it allowing it to leak. Shine a flashlight down there, and if there's oil pooled in that area, that's your culprit. Unfortunately, yes, it's blocked by the rear head. What most people do is lift it up as high as possible and clean it and the block as well as possible. Some sandwich a thin O-ring under it, others RTV it. My memory is hazy, but I think I may have done both. On my pic, high pressure oil-resistant RTV is the stuff kind of squishing out from under it. It's dirty because this was many years later, but it worked great. Official GM procedure is to pull the rear head, but that's way, way too much trouble.

This is an excellent point, can you pinpoint and/or provide a photo as to where this is? For the life of me I can't find it and/or provide the page on the 1994 W Book that may provide a diagram where it is located? I would really prefer not to pull the motor if that can be avoided. Thanks for this memo, much appreciated

Hmmmmmmmmm......no 72 ragtop's here the last time looked, pretty sure a 72 is an A body

I’m looking for the left driver side rear top rail. It connects to the left rear panel.. Need asap

I’m looking for the left driver side rear top rail. It connects to the left rear panel.. Need asap

You probably already checked, but make sure it's not the distributor plug seal before tearing into it. That can mimic a rear main seal leak.

I bought some decades ago to do the same thing, but never got around to it. I was going to try to mod them for 6.5" speakers and needed a plan for how to mod the buckets, but in the modern day, it would make more sense to 3D print some custom ones rather than mod the OEM ones as I wanted to use the OEM grilles which are flat against the trim panel. I can't find them at the moment or I'd snap a pic. As for prewired, my 89 wasn't prewired, but different years might do things differently.

Thank you. See, this is why I love this site. I'm still going to see if I can make it work. I'll have to add speaker grilles in any event because my car doesn't have the speakers.

I think the mounts will fit the doors, but I don't know that they'll fit under the door panels. 95-96 used 5.25" in these angled enclosure pod things that stick out quite a bit while 88-92 used 4x6's on a flat plate.

91-93 88984224 94-95 12480745 Hope that helps.

FR9. Hope that helps.

There are various designs...plastic or steel.......seeing as you don't intend on getting into this sort of repair again I'd suggest just picking up the plastic set, you should be able to find them at Harbor Freight. The inlet (pressure side) is 3/8 as for a gas can..really up to you..pick up a pair of containers that will hold a total of 15 gals?

Lifting the car isn't an option so I'll run out to gab the device. Thanks. Any idea what size clear tub would work? Don't have any spare garden hose to sacrifice.

This is the only device that will separate the fuel line from the rail.... there is another method you might try.... raise the car up high enough to get under comfortably & disconnect the fuel filter from the fuel line (one end of the filter makes used of threaded connection , the other end is the same ac/fuel line quick disconnect slip-on connection). Once again run a length of hose long enough to clear the car & fill a gas container to drain the tank.

Can i make due without this specialized tool? Don't want to buy something for what might be one time.

The fuel lines that feed the fuel rail are not screw on nut fittings, both the pressure & the return are disconnected with a set of fuel line/ac disconnect tools. The pressure line is near the centre at the back of the engine. One pulls off the engine cover & you'll see the fuel rail. Once you've disconnected the line you'll need a lengthy section of garden hose to slip over the fuel line end & tape it up to prevent any leaking & feed it into a container size of your choosing. Now you can bypass the relay to power up the fuel pump to drain the tank.

3800

Hmmmmmmm....3100 or 3800 engine?