Jump to content

This is what a bad strut bearing plate looks like


Hairdo12
 Share

Recommended Posts

Pictures speak for themselves:

SANY0490.jpg

 

SANY0482.jpg

 

SANY0483.jpg

 

The task really wasn't that hard, just took my time. I strongly believe there is no way you can get the center axle nut off without an impact. It wouldnt budge with a 24 inch breaker but the impact twisted it off in about 45 seconds. I then used a two jaw puller from harbor freight ($13 for three) to push the axle out of the wheel bearing. Of course I sprayed everything down with PB blaster the night before to help with the rust. Since the spring is shaped like a cone I used two sets of spring compressors because I was paranoid.

 

SANY0491.jpg

 

Here is how much I had to compress the spring to get the upper mount back on. If you have an impact, you don't need the special tool, just beat up on it with your 15/16 socket. I reused the isolator as it looked just fine to me.

 

SANY0492.jpg

 

Getting the assembly out I was able to do just fine by myself, but since I'm not a big guy I needed a helper to get it back into the wheel well. Once I got the upper mount in it was a one person job again.

 

If you're unsure about your bearing plate, I found a good test to be when the car is on the ground, grab the bearing plate and try to turn it side to side. It should move about 3/4 of an inch side to side. My drivers side was frozen solid, passenger moved freely like the new one does.

 

Oh one final thing, before I started I made numerious marks with a sharpie on the spring, isolators, mounts and strut assembly so I could line everything up the first time. I'm sure I would have been pretty pissed if I had to do something over.

 

What it looks like with the assembly out

 

SANY0489.jpg

Link to comment
Share on other sites

i wish i had pictures. mine was waaaay worse than that lol. but i will warn you i messed up my springs compressing them in that routine. i ended up having to get new bottom plates, bearings, springs, top plates, and mounts. it is hard to see it but when you decompress the spring all the way you can see it.

Link to comment
Share on other sites

What size is the axle hub nut? 34mm?

 

 

36mm

 

35mm.

 

Everyone around has said 36mm when I asked, so thats the socket I bought. I pretty much got most of my info from z34phoenix's website: http://z34phoenix.piczo.com/?g=48667619&cr=6

 

The 36 did seem like it could be a little smaller when I put it on the nut. I think my chiltons says 36 too, but I'd have to check (its 8 miles away right now).

 

Am I just crazy?

Link to comment
Share on other sites

I use a 1 3/8" socket, usually from a 3/4" drive socket set. When putting it back on I used the same socket with an adapter to use a half inch drive torque wrench and torque it to 182ft lb. (factory spec)

 

Jamie

Link to comment
Share on other sites

It is 35, but 36 fits. Somebody had even posted pics with proof of these because nobody believed him.

 

Werd.

 

Damn I thought it was just the bushing not the whole metal piece!!!

Link to comment
Share on other sites

It is 35mm, but I used a 36mm.

 

It took about an hour to remove the assembly another hour to replace the plate and about two hour to get everything back together. I took my time and triple checked everything. I only had a helper for 10 mins to get the thing back in. You may want to allow more time if your ball joint needs to be replaced. Remeber to pb blaster the night before!

Link to comment
Share on other sites

ya, well the guy at the shop today said he would do it for $150, so I am droppin it off in the AM... that's well worth the time it would take me and my friend to do it... lol

Link to comment
Share on other sites

  • 8 years later...

BUMP! Crazy old thread, lol. Does anybody know what holds the bearing plate onto the lower part of the assembly? I might take mine apart today and clean it or replace it but I can't get too crazy with it because I'm redoing the entire suspension with upgrades soon.

Edited by Imp558
Link to comment
Share on other sites

BUMP! Crazy old thread, lol. Does anybody know what holds the bearing plate onto the lower part of the assembly? I might take mine apart today and clean it or replace it but I can't get too crazy with it because I'm redoing the entire suspension with upgrades soon.

Gravity. it just sits on there.  Make sure you line it up right.  The spring will hold it in place once it's all back together. 

Link to comment
Share on other sites

Thanks for this post and the pictures.  I just saw it, and I have to do the job on my passenger side.  The drivers side failed catastrophically due to rust and fatigue in rural Montana last spring.  Had to have it towed and buy a whole new assembly from a wreck :(.

 

2h335fp.jpg

Link to comment
Share on other sites

Join the conversation

You can post now and register later. If you have an account, sign in now to post with your account.

Guest
Reply to this topic...

×   Pasted as rich text.   Paste as plain text instead

  Only 75 emoji are allowed.

×   Your link has been automatically embedded.   Display as a link instead

×   Your previous content has been restored.   Clear editor

×   You cannot paste images directly. Upload or insert images from URL.

 Share

×
×
  • Create New...